Cookies de la web de Omega
Utilizamos cookies en la web. Estas cookies son esenciales para que la web que funcione correctamente. Si sigue sin cambiar la configuración, vamos a suponer que usted está dispuesto a recibir todas las cookies de este sitio web.

Para obtener más información acerca de las cookies, por favor haga clic aquí
Cerrar
Cesta  |  Contacto  | 
En España 800 900 532
Fuera de España(+34) 911 776 121

AC Powered AC Input DIN Rail Signal Conditioner

DRI-AC

AC current and voltage transmitter | DRI-AC

AC current and voltage transmitter

371,00 DRI-AC

CE
  • Provides an Isolated DC Voltage or Current Output in Proportion to an AC Voltage or Current Input
  • 3-Way Isolation Eliminates Earth Loops
  • AC Voltage Ranges: 100 mV, 200 mV, 500 mV, 1 V, 2 V, 5 V, 10 V, 20 V, 50 V, 100 V, 200 V, 300 V
  • AC Current Ranges: 10 mA, 20 mA, 50 mA, 100 mA
  • Touch Calibration Technology
  • Universal AC Powered, 85 to 265 Vac
Instrumentos de medición y control de proceso - Ver productos relacionados

Descripción

The DRI-AC is a DIN rail mount, AC input signal conditioner with 1800 Vdc isolation between input, output and power. The field configurable input and output offers flexible, wide ranging capability for scaling, converting or buffering AC inputs ranging from 5 mA to 100 mA AC or 50 mV to 300 Vac.

For current inputs above 100 mA, it is recommended that an input shunt resistor be used and the DRI-AC be configured for the proper input range. For example, a 5A current transformer output can use a 0.1 Ohm, 5 W shunt resistor with the input of the DRI-AC set for 0 to 500 mV AC.

The DC output of the DRI-AC is proportional to the average of the fully-rectified AC input signal, and is calibrated for sine waves between 40 to 400 Hz.

To set the input level within the dip switch configured range, simply apply the high input signal (voltage or current) and push the CAL button. The low input signal is then applied and pushing the CAL button again stores the low input signal. The high and low input levels are stored in non-volatile memory and correspond to the high and low output levels. These output levels are precisely adjusted using the input signal.

The DRI-AC can be configured for input ranges from 50 mV to 300V or 5 mA to 100 mA, with >90% input offset or it will adjust down to <10% of full scale input span (except on the 100 mV/10 mA range in which maximum offset or gain adjustment is 50%).

The factory default configuration for the DRI-AC is as follows:
Input Range: 0 to 500 mV
Calibrated Output: 4 to 20 mA

Specifications
INPUT
AC Voltage:
    Ranges: 100 mV, 200 mV, 500 mV, 1 V, 2 V, 5 V, 10 V, 20 V, 50 V, 100 V, 200 V, 300 V (dip-switch selectable)
    Impedance: >100 kΩ
    Overvoltage: 330 Vac
AC Current:
    Ranges: 10 mA, 20 mA, 50 mA, 100 mA (dip-switch selectable)
    Impedance: 20 Ω, typical
    Overcurrent: 170 mA AC
    Overvoltage: 60 V peak
Frequency Range: 40 to 400 Hz, factory calibrated at 60 Hz
Common Mode (Input to Ground): 1800 Vdc max
Push-button Adjustment: Max. zero offset and span turn down is 50%

OUTPUT
Voltage Output:
    Range: 0 to 5V, 0 to 10V (dip-switch selectable)
    Source Impedance: <10 Ω
    Drive: 10 mA max (1 kΩ min @ 10V)
Current Output:
    Range: 0 to 1 mA, 0 to 20 mA, 4 to 20 mA (dip-switch selectable)
    Source Impedance: >100 kΩ
Compliance:
    0 to 1 mA: 7.5V max (7.5 kΩ max)
    0 to 20 mA: 12V max (600 Ω max)
    4 to 20 mA: 12V max (600 Ω max)
LED Indication:
    RUN (Green): On when unit is powered; flashes at 8 Hz when input is 7% above max
    INPUT (Yellow): On while calibrating the input level
    OUTPUT (Red): On while calibrating the output level
Accuracy (Including Linearity & Hysteresis): ±0.1% of span typical, ±0.2% max; ±0.5% of span max (100 mV range)
Temperature Stability: ±0.025%/°C of selected input span, typical
Response Time (10 to 90%): 250 mSec, typical
Common Mode Rejection (DC to 60 Hz): 90 dB
Isolation: 1800 Vdc between input, output and power
Operating Temperature: 0 to 55°C
Storage Temperature: -25 to 70°C
Humidity (Non-Condensing):
    Operating: 15 to 95% RH @ 45°C
    Soak: 90% RH for 24 hours @ 65°C
Power: 100 to 240 Vac ±10%, 50 to 400 Hz; 1.5 W typical, 2.5 W max
Wire Terminations: Screw terminals for 12 to 22 AWG wire
Weight: 218 g
Realizar Pedido(Especifique el número de modelo)
Número de pieza/Desc.
Cant.
Descripción
Quick Ship
DRI-AC
371,00
Stock: 9 semanas
 
AC powered AC input DIN rail signal conditioner
Accessories
Quick Ship
ACPB-2
€31.50
Stock: 9 semanas
 
AC power distribution bus for 2 modules
Quick Ship
ACPB-4
€81.00
Stock: 9 semanas
 
AC power distribution bus for 4 modules
Quick Ship
ACPB-8
€110.00
Stock: 9 semanas
 
AC power distribution bus for 8 modules
Todos los precios se muestran en EUR
Notas: An ACPB power rail is required to power the modules and is ordered separately.
Ordering Example: (1) DRI-AC AC powered AC input DIN rail signal conditioner, €371.00  plus (1) RAIL-35-1 35 mm DIN rail, 1 metre, €10.25, €371.00 + 10.25 = €381.25